Post a reply to the thread: braze mini-split vs flare connections ?
You may choose an icon for your message from this list
Please enter the name by which you would like to log-in and be known on this site.
Please enter a password for your user account. Note that passwords are case-sensitive.
Please enter a valid email address for yourself.
Will turn www.example.com into [URL]http://www.example.com[/URL].
Press them. No flare no fire no leaks.
Originally Posted by pecmsg Then Start a N E W Thread! Why? This is the perfect place to discuss flare vs braze issues.
Originally Posted by Sapote If using clutch type flare tool: 0 to 0.02" stubbed for 1/4" and up to 5/8 pipes. Many people have too much length of the flare. Then Start a N E W Thread!
Knowledge has no expiration date. This is why some people seem to learn very little as they think they are getting old.
*
Originally Posted by GAchillrtek good rule of thumb is about a nickels width of copper stubbed out on your flaring block, and oil while flaring and on your flare nuts while tightening, and a torque wrench you should be good to go. If using clutch type flare tool: 0 to 0.02" stubbed for 1/4" and up to 5/8 pipes. Many people have too much length of the flare.
Originally Posted by y7turbo Holy hell thats one big POS just like the rest of the jap systems. We just did a couple Panasonic Eco I VRF systems, 2 condensers and 22 indoor units on one reefer circuit.. All brazed pipe on the mains, suction, hot gas, and liquid, solenoid boxed were brazed as well but flared connections at the indoor unit. YES . The bad part is i came onto the job after they "flared everything" and the forman on the job is never there, riding the clock. Well me and another guy ended up pulling every unit off the wall and reflaring, also a bunch on the bc controller. its was a nightmare!! ive been playing cleanup on that job for 3 weeks. We got 600 lbs of nito in it thursday, SURE HOPe its all in there monday! The moral of the story is make sure you are flaring properly and you shouldnt have a problem, good rule of thumb is about a nickels width of copper stubbed out on your flaring block, and oil while flaring and on your flare nuts while tightening, and a torque wrench you should be good to go. theses guys didnt even have a torque wrench when i got there
Originally Posted by david912 Attachment 316431 Holy hell thats one big POS just like the rest of the jap systems. We just did a couple Panasonic Eco I VRF systems, 2 condensers and 22 indoor units on one reefer circuit.. All brazed pipe on the mains, suction, hot gas, and liquid, solenoid boxed were brazed as well but flared connections at the indoor unit.
Originally Posted by jnsrose Just curious what torque wrenches you use for flare nuts and where can I buy them. http://www.cpsproducts.com/#/p-hand-...enches-tltwsm/ Here's what I bought. I think I found them online, but I don't recall where. Model TLTWSM.
Originally Posted by jnsrose Just curious what torque wrenches you use for flare nuts and where can I buy them. I used to cut flares and braze. It did bite me in the a$$ when I returned an indoor unit for warranty and they wouldn't cover it. Now it's flare only indoor and outdoor and braze with nitro on intermediate piping. As stated already, driers are a no-no on most units. I did install a carrier once that came with a drier. Different design. United sells the torque wrench set for mini-splits, they are about $60. Some Mitsubishi "authorized diamond trainers" are making their own rules when it comes to installation and repairs of mini-splits, Meier supply is one of them, their trainer is a clueless clown and he makes stuff up as he goes, when doubt call Mitsubishi, remember if the parts counter guy was any good, he would be on the field making more money.
Originally Posted by kdean1 At the recent Mitsubishi Diamond Contractor class we asked about brazing. The instructor said there is no objection to brazing provided proper procedures are followed - clean the joints, trickle nitrogen and use 15% silver content solder. However, he said flaring should not be a problem if a good flaring tool is used and a torque wrench is used for tightening the flare nuts. Also make sure to use the flare nuts that come on the equipment, NOT hardware store flare nuts that cannot withstand the pressure of R410-A. Just curious what torque wrenches you use for flare nuts and where can I buy them. I used to cut flares and braze. It did bite me in the a$$ when I returned an indoor unit for warranty and they wouldn't cover it. Now it's flare only indoor and outdoor and braze with nitro on intermediate piping. As stated already, driers are a no-no on most units. I did install a carrier once that came with a drier. Different design.
How are you guys that braze flowing N2? Almost all the minis i've installed only have 1 access port for each head.... Anyway I always flare ad use the cps tool that has the deeper v on the block to get a nice flare with maximum surface area. Oil on the flare nuts and the flare goes a REAL long way toward leaks. I Vacuum to 100 microns or so and hold it under 500 for 30-60 minutes. I do mostly Fujitsu and Lennox (Gree) Brand, sometimes Mitsu.
At the recent Mitsubishi Diamond Contractor class we asked about brazing. The instructor said there is no objection to brazing provided proper procedures are followed - clean the joints, trickle nitrogen and use 15% silver content solder. However, he said flaring should not be a problem if a good flaring tool is used and a torque wrench is used for tightening the flare nuts. Also make sure to use the flare nuts that come on the equipment, NOT hardware store flare nuts that cannot withstand the pressure of R410-A.
Thanks guys, learned some things about mini-splits. Will stay with the flare and do the 600 psi N2 test and 24 hr vac also.
Originally Posted by mattt787 i went to a city multi class they said to flare only no brazing they want a presser test up to 600 psi on there system and oil tool and copper We flare everything except on the branches that we run multiple heads on one branch. Where they tee off I flowed nitro and brazed them. Yes, pressure test at 600 psi for 24 hours. Then hold <500 microns for 24 hours. To the OP, make a good flare and it will be just as good as any braze joint. When people have trouble with flares, it is invariable due to a poorly made flare.
i went to a city multi class they said to flare only no brazing they want a presser test up to 600 psi on there system and oil tool and copper
flares only, no flames on minis!!!!!! I have not seen that it voids warranty, but makes sense. they are trying to idiot proof the install. have not had a failed flare in our company, that I am aware of, in the approximately 400 units installed by us.
we have a city multi going on now, 19 Ah and flares on everything Attachment 316431 thats the main Bc controller, theres also a sub bc controller, Alot of flaring!! i feel like a pro at flaring now. make sure you have the right flare tool and oil your tool and copper while flaring. The less brazing you do the better, nito is a must if you have to. No driers or sight glasses. They dont want brazing bc the system dosent have diers and driersshouldnt be installed
If its a wall mount i usually cut them off and braze them, then you've only got flares on the outdoor unit where its easy to check, the pipes are then easier to run through a wall or behind the unit without the bulk of the nuts etc. But it depends on the make, some units have little straines just after the flares so you can't cut these. No driers or sightglass, its an expansion line not a liquid line. Insulate both lines or it'll sweat. Measure the lineset as you go, and calculate the charge by the oz per foot/grams per meter chart, can't use subcool superheat with these. Best advice i had when starting to fit these is read the instruction before you start, they often bring out slightly different models or change the spec etc and it will catch you out otherwise.
i have gone to a few Fujistu courses and they have said if you weld the warranty is voided
Forum Rules