Reply to Thread

pretty sure the older one also uses the 150 # transducer, local sporlan shop can get it for you Part # 952572

Dongle and control are proprietary to Hillpxh (was built by sporlan though)

you can easily convert SMS to a KELVIN II controller using existing valve sensor and transducer, easy if superheat only, i think you should use the chiller one or the subcooler one if you also need temp control, just make sure what your SMS is doing to decide.

Mike

Can you still GET transducers and sensors for the older systems?

Sure would be nice to be able to find a supply. Nobody around here that I've spoken to seems to be able to find them.

But while were on this subject, here is a post from a couple years ago showing the use of some technology to troubleshoot the issues you are describing: http://www.midtennrses.net/2014/08/u...-troubleshoot/

Our company supplied us with one of these dongles from HP and I am not sure where you can purchase one other than from them. Getting it all walking and talking can also test your computer skills; ports, software, drivers, etc.

Sporlan should take some credit for the flaws with these control systems. We have a company policy that if it doesn't take a sensor or transducer to get it going, then cut it out and go conventional. Always remember that you will have to connect an external equalizer line to the setup. You can probably use the port that is left from where the transducer was connected.

JaaGeeGee

Sorry to bring up an old post.

Anyone know where I could buy one of these over prices USB Dongles other than Hill Phoenix?

SMS sucks.

I wish the device and assembly also had DA.

Originally Posted by Icanfixitall

What happened at Hill Phoenix?

Have you worked on their stuff???

Originally Posted by Phase Loss

Neither.

It's just, I had recent bad experience with Hill is all.

I like Zero Zone stuff.

What happened at Hill Phoenix? And zero zone, oh boy that's some junk...

Originally Posted by VTP99

That Zero Zone stuff is quality for sure. The last one I serviced was built like a tank.

Meh..... I helped out on a startup in a ZZ store.

Neat stuff, smart factory guy, but no more special than anything else I've seen.

Almost 100% of the new equipment we're installing is H/P or Barker. I've set up quite a few of these EEVs recently.

Suction temperatures have been moving upwards over the past 10 years or so.

Meat cases used to want to run at 12 degrees SST. Now, I'm setting them at 18-20SST and getting the same or better product holding times. Better designs.

Newer case, I'd start at 18 SST or so, and see where it goes from there.

What I'd do is measure the SH. If it isn't high then I'd either start by replacing the transducer, then the temp sensor OR, I'd do as blackmira suggested and break out the Q kit, IF and ONLY IF, the case is over 12 months old.

Our company got burned on one where a guy did that. H/P rep walked in, looked at the case and said "You modified it, warranty void" Customer made us put an EEV back in the case. Almost all of us carry transducers and sensors. One guy in each region carries a laptop and a dongle.

Lately, I'm tending to agree with Phase Loss. Hill/Phoenix sure ain't all that excellent on the quality side of things. Too many little details that aren't right.

Originally Posted by Phase Loss

Neither.

It's just, I had recent bad experience with Hill is all.

I like Zero Zone stuff.

That Zero Zone stuff is quality for sure. The last one I serviced was built like a tank.

Originally Posted by VTP99

You must be a Kysor/Warren or Hussmann guy.

Neither.

It's just, I had recent bad experience with Hill is all.

I like Zero Zone stuff.

Originally Posted by Phase Loss

Hill Phoenix and smart don't belong in the same sentence, not even the same thread.

You must be a Kysor/Warren or Hussmann guy.

Originally Posted by Blackmira

We carry a Q body kit for these gems

The thought crossed my mind. But what a shame to waste all that advanced technology.

Hill Phoenix and smart don't belong in the same sentence, not even the same thread.

We carry a Q body kit for these gems

Originally Posted by jpsmith1cm

I suppose that wild swings in system operating conditions could make the valve hunt, but under relatively constant conditions, they're TIGHT! They'll run a nice, low superheat and keep it pretty tightly controlled with a minimum of hunting.

My understanding was that the dongle was about $400. I didn't buy it, though.

I suppose that you could troubleshoot these systems by 'guess and golly' but I've found that a laptop and the dongle make it much easier and more accurate.

Thanks jp,
So it sounds like you got your company to shell out the shillings for you....nice. Unfortunately this cheap a$$ is not going to do that. I'm twisting his arm just to get a fan cycling control on it. I would much rather pipe in a proper head pressure control. This reach-in is using R404a at medium temp. What should the coil temp. be running at ? I was at about 15* if I remember correctly. Hill Phoenix is showing a 6-8* superheat. I was getting a yellow/red led which is a high superheat code. Also the case is on a time clock for time defrost is that necessary ?
Thanks VTP

Originally Posted by VTP99

Sounds like the same setup. The way I'm seeing it you have to use a IR device that plugs into ones laptop then shoot it at the possessor. This is the only way to reprogram it for a different refrigerant use. That's not what I'm after though. Was just curious if one can troubleshoot the plugins. I know the first thing I need to do with the one I'm working on is to get the outdoor unit on some type of head pressure control. Will these valves hunt like the mechanical valves ? How much is the dongle ?

I suppose that wild swings in system operating conditions could make the valve hunt, but under relatively constant conditions, they're TIGHT! They'll run a nice, low superheat and keep it pretty tightly controlled with a minimum of hunting.

My understanding was that the dongle was about $400. I didn't buy it, though.

I suppose that you could troubleshoot these systems by 'guess and golly' but I've found that a laptop and the dongle make it much easier and more accurate.

Originally Posted by jpsmith1cm

You mean the Hill Phoenix SMS system.

The Electronic Expansion valve that requires a FREE software download and an outrageously priced USB Dongle to program or communicate with?

The same system that they're installing on their Glycol "semi-self-contained" systems, attaching the controller to the bottom of the drip pan and wondering why they burn out?

Nope.... Never worked on one....... This week....





Whaddya need to know?

Sounds like the same setup. The way I'm seeing it you have to use a IR device that plugs into ones laptop then shoot it at the possessor. This is the only way to reprogram it for a different refrigerant use. That's not what I'm after though. Was just curious if one can troubleshoot the plugins. I know the first thing I need to do with the one I'm working on is to get the outdoor unit on some type of head pressure control. Will these valves hunt like the mechanical valves ? How much is the dongle ?

Originally Posted by jpsmith1cm

I'd carry a couple transducers....