PDA

View Full Version : I Need Help With Staefa Controls !!!!!!!!



Recovery Unit 1
02-19-2009, 06:32 PM
PLEASE ,:confused: PLEASE,:( PLEASE, :eek: I need to make a cable, that will allow me to use Staefa PC tool Version 5.0 to com with Staefa Smart ll / Standard cards (siemens) .... PC tool to SM2-DDC V2.2 U7 . Thanks, RU1

d ward
02-20-2009, 11:14 AM
You got mail hope you can read it. Sorry I will send it again and attach it this time.

Recovery Unit 1
02-21-2009, 06:17 PM
Ok , The Pinout in the training manual is not the one I need .. Everyone is sending me that one, and I apperciate it. Thank you. The Smart ll cards only accepts an Rj-12 6-pin a Rj-45 8-pin does not fit... So I need a Db-9 to Rj-12...

jogas
02-21-2009, 07:48 PM
Ok , The Pinout in the training manual is not the one I need .. Everyone is sending me that one, and I apperciate it. Thank you. The Smart ll cards only accepts an Rj-12 6-pin a Rj-45 8-pin does not fit... So I need a Db-9 to Rj-12...

Staefa sold a DB9 to RJ12 adapter, and also their RJ to RJ cable.
I cannot find the pinout for the adapter, but I know the cable colors are the same if you hold both RJ ends side by same side. Don't know what it's called as I can never remember if it's a crossover or straight thru as my Dell auto-detects and does it automatically for me.

Recovery Unit 1
02-22-2009, 09:51 AM
Jogas , Thanks for trying to find the pin-out ! I apperciate the effort.

jogas
02-23-2009, 07:20 AM
Well, whataya know,
I finally found the "Workstation DB-9 to Staefa Net Controller" Pinout:

Controller RJ-12*
Pin Number below left:
2--RXD--------<<<------TXD--3
3--COM-----------------COM--5
5--TXD-------->>>------RXD--2
Workstation DB-9 (Com Port)
Pin Number above right:

(RJ on the left, DB-9 on the right. HAd to do it this way as the text editor stacks text and doesn't allow gaps)
* RJ-12 plugs into the RS-232 (RJ jack) of Host A or B of the Node.
Check and match your Port/PC baud rates, and slow down the buffer settings.
Good luck,

jogas
02-23-2009, 05:42 PM
I answered your PM, but I'll post here for all.
I cannot find the SM2 Tool adapter/cable pinout.
But you can use PCTool to "tunnel" thru the Node to get to an SM2 card, just a slower connection.

Recovery Unit 1
02-24-2009, 06:33 PM
JoGas , YOU CAN FIND IT , I Have Faight in you !!!!!!!!!!!!!!!!!!!!!!!! RU1

jogas
02-25-2009, 07:41 AM
JoGas , YOU CAN FIND IT , I Have Faight in you !!!!!!!!!!!!!!!!!!!!!!!! RU1

You've got mail....enjoy.

Recovery Unit 1
02-25-2009, 07:58 PM
JOEGAS IS THE MAN !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!:):):):):):):):):):):):

Recovery Unit 1
02-25-2009, 08:08 PM
Joe, my Friend Joe in 12th Grade could not line lock his 68 SS , But I Did !! He was pissed ... Ha Ha Ha.................. Thanks Again RU1 , Dave